Did you just try to flush your toilet, and nothing occurred? Look into the tank, and you could see no water inside. Before you worry, rest assured that repairing this problem is usually easy to accomplish. If you can’t figure it out yourself, you can always schedule toilet repair with an Expert plumber. Follow these tips to diagnose and repair the problem of no water in the toilet tank.
Check the Water Supply
The first move is to make sure the water is running. If you or someone in your household recently did a toilet repair, you probably turned off the water first. Did you forget to turn it back on? To check, turn the water shut-off valve on the wall behind the toilet. If the valve was turned off, water ought to now start refilling the tank. If this fails to work, test the water at your sink or an alternative plumbing fixture. If nothing spills out from the tap, you could possibly have a larger water supply issue. Call your water company to get more details.
Reposition or Replace the Float Mechanism
Older toilet models use a float ball to measure the water level as it goes up in the tank. When the ball hits a specific height, the float arm it’s attached to stops the water flow. However, insufficient water may enter the tank if the ball is positioned incorrectly or the arm is faulty. To move the float ball, start by removing the toilet tank lid. Bend the float arm up slightly to change where it sits in the tank. If this does not fix the problem, you might need to replace the full float mechanism. You should be able to perform this yourself by following the detailed steps that come with the replacement parts, or you can employ a plumber for help. Just note that float balls are old toilet technology. You may enjoy improved reliability and efficiency if you upgrade the existing tank components or replace the toilet altogether.
Adjust the Fill Valve
Newer toilets utilize a float cup in place of a float ball, coupled with a fill valve and water level rod. There may be no water in the toilet tank because the valve has slipped out of place or become blocked. Here are a couple tips to try:
- Test the fill valve: Have a look inside the toilet and find the fill valve on top of a vertical tube device on the left side of the tank. Make sure it’s secure and evenly attached to the tube. Then, fine-tune the water level. Newer toilets have an adjustment knob you can turn manually, while older versions may require you to loosen an adjustment screw with a flathead screwdriver. Flush the toilet and make it possible for the tank refill to check the water level. Modify it until the water comes to approximately one inch below the top of the overflow tube.
- Clean the fill valve: Mineral buildup and other crud could be covering the valve and stopping your toilet from filling. Shut off the water behind the toilet and take off the fill cap. Then, gradually turn the water back on, cupping your hand over the valve to prevent water from spraying all over. After several seconds, turn the water back off. Finally, scrub the fill cap to remove hard water buildup. If the cap is damaged, replace it.
- Clean the valve tube: The tube below the fill valve could also be clogged. Shut off the water and take away the valve hardware. Then, insert a slim bottle brush or wire down the tube. Turn the water back on slightly to flush away the blockage. Replace the valve hardware and flush the toilet to check your adjustments.
Repair or Replace the Trip Assembly
If you’ve attempted the steps above without positive results, the last possibility is a damaged trip assembly. This component connects the flush handle to the tank. If it’s damaged or positioned inadequately, the flush cycle may not complete, leaving the tank empty. Remove the toilet tank lid and check the trip assembly attached to the handle. If it’s out of place, reposition it. If the assembly is crooked, worn or busted, replace it. Whether you perform the job yourself or leave it to a plumber, this simple repair should get your toilet tank filled with water once more.
Schedule Toilet Repair Today
You can’t go long without a working toilet, so reach out to [Company name] to schedule a toilet repair. We can determine why your toilet isn’t filling and suggest the correct fix. If your plumbing fixture is older and worn out, our team will install a high-efficiency toilet in your bathroom. Be assured that every plumbing repair and replacement we conduct is backed by a 100% satisfaction guarantee. To schedule a visit from one of our licensed team members, please call your local Eveready Service Experts office today.